Archive for August, 2009

Aug 30 2009

Discharge Battery Methods

Published by admin under battery tips

Tracking back: http://www.batteriesshop.co.uk/batteries/2009/07/15/discharge-battery-methods/

The purpose of a battery is to store energy and release it at the appropriate time in a controlled manner. Being capable of storing a large amount of energy is one thing; the ability to satisfy the load demands is another. The third criterion is being able to deliver all available energy without leaving precious energy behind when the equipment cuts off.

C-rate

The charge and discharge current of a battery is measured in C-rate. Most portable A31-S5 batteries, with the exception of the lead acid, are rated at 1C. A discharge of 1C draws a current equal to the rated capacity. For example, a battery rated at 1000mAh provides 1000mA for one hour if discharged at 1C rate. The same battery discharged at 0.5C provides 500mA for two hours. At 2C, the same battery delivers 2000mA for 30 minutes. 1C is often referred to as a one-hour discharge; a 0.5C would be a two-hour, and a 0.1C a 10 hour discharge.

The capacity of a battery is commonly measured with a battery analyzer. If the analyzer’s capacity readout is displayed in percentage of the nominal rating, 100 percent is shown if 1000mA can be drawn for one hour from a battery that is rated at 1000mAh. If the A31-S6 battery only lasts for 30 minutes before cut-off, 50 percent is indicated. A new battery sometimes provides more than 100 percent capacity. In such a case, the battery is conservatively rated and can endure a longer discharge time than specified by the manufacturer.

When discharging a battery with a battery analyzer that allows setting different discharge C-rates, a higher capacity reading is observed if the battery is discharged at a lower C-rate and vice versa. By discharging the 1000mAh battery at 2C, or 2000mA, the analyzer is scaled to derive the full capacity in 30 minutes. Theoretically, the capacity reading should be the same as a slower discharge, since the identical amount of energy is dispensed, only over a shorter time. Due to energy loss that occurs inside the battery and a drop in voltage that causes the A32-A8  battery to reach the low-end voltage cut-off sooner, the capacity reading is lower and may be 97 percent. Discharging the same battery at 0.5C, or 500mA over two hours would increase the capacity reading to about 103 percent.

The discrepancy in capacity readings with different C-rates largely depends on the internal resistance of the battery. On a new battery with a good load current characteristic or low internal resistance, the difference in the readings is only a few percentage points. On a A32-M9 battery exhibiting high internal resistance, the difference in capacity readings could swing plus/minus 10 percent or more.

One battery that does not perform well at a 1C discharge rate is the SLA. To obtain a practical capacity reading, manufacturers commonly rate these batteries at 0.05C or 20 hour discharge. Even at this slow discharge rate, it is often difficult to attain 100 percent capacity. By discharging the SLA at a more practical 5h discharge (0.2C), the capacity readings are correspondingly lower. To compensate for the different readings at various discharge currents, manufacturers offer a capacity offset.

Applying the capacity offset does not improve A32-S5  battery performance; it merely adjusts the capacity calculation if discharged at a higher or lower C-rate than specified. The battery manufacturer determines the amount of capacity offset recommended for a given battery type.

Li-ion/polymer batteries are electronically protected against high discharge currents. Depending on A32-S6 battery type, the discharge current is limited somewhere between 1C and 2C. This protection makes the Li-ion unsuitable for biomedical equipment, power tools and high-wattage transceivers. These applications are commonly reserved for the NiCd battery.

No responses yet

Aug 30 2009

Laptop battery maintenance guide

Published by admin under battery tips

 Tracking back: http://www.batteriesshop.co.uk/batteries/2009/07/16/laptop-battery-maintenance-guide/

Battery is the consumables, with a limited life expectancy, most manufacturers warranty for the notebook battery time ranging from three months to a year, Dell is to follow industry standards to provide a limited warranty for one year. For batteries, use the correct and proper storage, can significantly extend the  battery life of notebook computers.

First, the battery useing must follow some attention points.

1. When you use laptop with external power, you dont need to take out the battery.

There is a chip to prevent over-charging in the mainboard. When the rechargeable battery power to 100% state of charge, the charge control chips (FET) will stop charging the laptop battery. We do not have to worry about damage to the battery.
Connect the  battery to avoid loss of BIOS information.
To prevent a sudden loss of power break.
2. To prevent exposure to prevent damp to prevent the erosion of liquid chemicals, batteries to avoid contact with metal objects, such as exposure to short-circuit occurrence.

3. Long-term do not use notebooks, how to store the laptop battery?

We will have a period of time not to use the notebook, the battery is fully charged to preserve, or to be released after save electricity?

Put long-term preservation of photoelectric dell gd761 battery will lose their activity and even lead to the control circuit protection self-locking and can not re-use, full of power will bring about long-term preservation of the safety problems, the best method is to save electricity use to 40 or so and then stored in cool dry place, about 20 degrees Celsius is the ideal storage temperature. Of course, the best month to come up with to use a battery, the battery can ensure a good state of preservation, but also does not allow the loss of electricity damage to the battery completely.

One response so far

Aug 28 2009

Second-hand laptop battery repair methods(2)

Published by admin under battery tips

The article come from http://www.mylaptopbattery.co.uk/blog/2009/08/27/second-hand-laptop-battery-repair-methods2/

The next is to give laptop battery block “disembowelling her”, and its shell, but using ultrasonic technology to weld together. At this time may be preceded by a careful look to see if the battery laptop battery block on which the cracks, what is the direction of these gaps, consider what should gaps prized open with a blade and the screwdriver. If it does not work, then, you can also power down the cell blocks of four weeks to iron casing hot to open. This step is especially important, if done well, done carefully, then to the battery block the appearance of little impact, doing well, and that the battery block will see significant recovery after the “scars” in.

To open the battery casing blocks later, we can see the internal structure of notebook computer batteries had. At this time, we can look at a single digital multimeter measured the battery voltage to low voltage battery removed, the appropriate use our mail order batteries replaced. Here we must remind some single-cell aging after their performance for the voltage drop is not, for such a cell we can use digital multimeter to 10A current file, the red pen then the table cell “+” pole, the black table briefly touch pen look at the battery “-” pole (1 second or so), take a look at the display multimeter values, instantaneous short-circuit current in general will reach more than 5A, if the deviation from this value is too large, less than 1A, then this section of the battery has failed, it have to replace! After such examination the future, if there is no one can use, then it must be replaced dell Latitude D410 battery,dell Latitude D420 battery.

Removed the old batteries in a time when 10 million should be careful not to put the laptop battery protection circuit broke, and its lithium battery, but “protection of God”, when the battery is fully charged when the charger will automatically turn off power when in use , when the voltage is below the protection value will automatically stop when the power supply, or they will come to naught.

Replaced with the new batteries to go before we make a single cell combined into needs specifications. An analogy, I use Fujitsu’s little red book, compact, lightweight, is used to playing to type, on the Internet just fine, and the notebook computer battery is a rectangular 7.2V 2400MAH, and with 3.6V 1.35AH shown in Figure 4 The single-cell lithium batteries, they have to use four such batteries, two and two put together (that is, the battery positive to the positive and negative electric soldering iron welded to the cathode, alas, if you are not even what is in parallel What is the series can not understand all the words would advise you to do hands-on), composed of two 3.6V 2700MAH battery packs, and then these two 3.6V 2700MAH battery packs together in series to form battery packs 7.2V 2700MAH (larger capacity than the original, using longer!), and fixed with adhesive tape is good, this time it can follow the first wife of your laptop battery wiring methods, the new batteries of the battery pack is soldered to the anode protection circuit board to . Different brands and models of laptop battery voltage, capacity may be different, but the space inside the battery box will be not the same, which is carrying out “for the core” operation before it requires us to take fully into account in order to do so with confidence.
Then there is the fixed battery, and the prepared hot melt adhesive stick, with hot air gun-opening (if there is no electric hot air gun soldering iron effects are good), the drop in place a few drops, you can wait until after the solidification of the the shell of the original laptop cover, and this relatively simple, first in the case of some strong glue on the painted (AB glue, etc.), then the other half shell Zhanshang Qu, and so after a period of solidification can be tested.

Here are just knee surgery want to activate a second-hand laptop battery deal is fully charged and discharged, so that the maximum capacity of lithium batteries to resume. Approach is, in the boot of the state to close all power management, turning the notebook slowly discharge until they are completely without electricity, and then fully charged (slightly over charge for a while), can be repeated two to three times normal use.
Is believed that after such a big “for core” After surgery, your beloved laptop turn to the surging power of the listen whenever and wherever you call dell Latitude D505 battery,dell Latitude D510 battery,dell Latitude D520 battery.

1,524 responses so far

Aug 28 2009

Second-hand laptop battery repair methods(1)

Published by admin under battery tips

The article come from http://www.mylaptopbattery.co.uk/blog/2009/08/27/second-hand-laptop-battery-repair-methods1/

Laptop has been enchanting charm, a vast number of computer enthusiasts, especially the young to pursue a family focus. The new laptop mostly in million yuan, due to the reasons for the laptop battery of non-biggest names in hard to accept; while second-hand laptop computer is relatively cheap, its function in general can be used to meet the need, and therefore second-hand laptop computer enthusiasts to purchase a minority.

However, the second-hand laptop, after all, is the second-hand goods, is used by others, and its uneven performance, compared with the new notebooks, the biggest difference is the built-in battery should be working hours, and better able to work a little 2-3 hours, poor or even 1 hour is not that, Imagine, such a battery, has just appeared in front of their friends gestures some low-power alarm, how much loss of face. Although the second-hand laptop computers also are equipped with AC power adapter, but if only relied on, and there is nothing different from the desktop dell Inspiron 8600 battery,dell Inspiron 9200 battery? Will lose the significance of the purchase of notebook computers.

In order to play a second-hand notebook computers advantages of moving their own, it is necessary to work on the battery. Laptop battery has been a large “books” fans feel is a very mysterious thing, that it how high technical content, does not. Here is a notebook computer batteries internal structure.

From which we can easily see that, by a number of individual cells in series and parallel together to form a battery pack, combined with the battery protection circuit, they constitute a laptop battery. Whether you use a notebook computer is what the brand, and its built-in battery’s internal structure are similar. If the internal use in accordance with the type of battery to points, most of them can be divided into nickel-cadmium batteries, nickel-metal hydride batteries, lithium batteries, lithium polymer batteries. The nickel-cadmium batteries, nickel-metal hydride batteries have a memory effect due to the capacity of small and other disadvantages are gradually being eliminated out, lithium-ion battery has a large capacity, small size, light weight, low self-discharge rate advantage has now become a series of notebook computer the mainstream of the battery set.

Second-hand notebook computers because of production age-old, after the use of a few years later, its battery much shorter working hours need to be replaced, various brands of laptop battery shape is different, not interchangeable, in order to buy into the same look and feel, the same model second-hand laptop computer batteries be prohibitively difficult. How to do? Of course, this DIY spirit of the fans have yet to be rattled! After using various means (such as software maintenance, charging and discharging several times the depth of activation, etc.), are invalid or effect.

But our own hands, the charges will not spend more than 50 yuan! Worth a try.

There is a tag line, said: “The biggest operation – completely changed”, I introduce to you today, tends to be scrapped is the right notebook batteries reborn surgery, the charge is not into electricity, reduce the capacity of the battery replaced. “Reborn” is mildly entertaining seems scary, very difficult to like, actually read the contents of the back you will understand, as long as a little with the practical ability of the fans are all successful, I believe you can do a back surgeon , to their notebook computer batteries surgery dell Inspiron B120 battery,dell Inspiron B130 battery.

Material preparation: electric iron, digital multimeter, blade, hot melt adhesives, hot air guns, a number of lithium batteries batteries (as the case may be) and so on, of course, if your laptop is used in the original nickel-cadmium batteries or nickel-metal hydride battery, in order to enhance the battery capacity, are replaced by lithium batteries is also not a bad idea is only a suitable lithium batteries batteries is too difficult to find them. Mail-order single-cell lithium battery, model is US18650, a single-capacity 3.6V 1.35AH, through a certain series, parallel combination, can be combined into different voltage, different-capacity lithium battery, so as to achieve the requirements of your beloved notebook.

Of course, it is possible laptop batteries batteries may not necessarily be such a cylindrical, if it does not work, then you can also buy rectangular lithium batteries, in short, according to your own laptop battery exterior and interior space to choice and decision dell Inspiron E1405 battery,dell Inspiron E1505 battery,dell Inspiron E1705 battery.

No responses yet

Aug 28 2009

Recommend two laptop battery repair software

Published by admin under battery tips

The article come from http://www.mylaptopbattery.co.uk/blog/2009/08/27/recommend-two-laptop-battery-repair-software/

The greatest advantage of laptops is mobility, provide the basis for all this is the battery. In the energy-saving technology and battery technology being a time when there is no breakthrough to fully optimize the battery and master the use of a number of related techniques would be helpful. However, laptop battery life is longer, often dissatisfied with the charge, and even shows the battery is damaged, it must pay particular attention to the use of certain skills dell Inspiron 6400 battery,dell Inspiron 640m battery.

First, choose the best time to repair
Laptop battery there is an inevitable part of aging, almost all of the repair methods are trial “deep charge deep-release” principle, in order to ease the laptop battery memory effect. Undeniably, however, the depth of the charge and discharge operation will not be good for the laptop battery itself, is a must not to do this method. If the battery life to merely reduce the dozens of minutes, then care should be taken to this method of operation. In addition, the pool of laptop battery manufacturers has been optimized, there is no self-depth again to upgrade the battery charge and discharge capacity argument. However, exactly when you need the depth of charging and discharging is very difficult to master, after all, every time the electricity consumed are not the same, it is suggested we BatteryMon with this professional software.

BatteryMon is a specifically for the small laptop battery monitoring software, especially for those who are not built-in power management chips and software, machine, it will undoubtedly help a lot of great help. BatteryMon most salient feature is able to discharge curve, and the installation will run automatically. A good performance of the battery will have a very regular discharge curve, as shown, basically a grid for every drop of time are probably the same. If found to have a very unusual beating, then it is necessary for cell “deep charge deep-release” repair.
Second, “deep charge deep-release” of the basic method
Batteries correction is an effective way to deal with aging batteries, in general, the various brands of notebooks will have a dedicated battery calibration software. For example, IBM’s ThinkPad series of discharge dedicated software, recommended for all to use IBM notebook users. But the program need to be repeated three times to get the best results. Download the software and the implementation of discharge, the system will be prompted to create installation disks. Use the installation disk boot PCDOS, unplug the AC power supply prompted, discharge the software will automatically discharge control. When everything after the notebook will automatically shut down, and then we can be connected to AC power for charging, time control in the 9 ~ 12 hours, repeated for 2 or 3 times can be.

For the laptop battery activation, our key software to find a suitable discharge. Unfortunately, if your laptop is not specialized discharge software, you can be shut down in the BIOS and Windows power management features, and then do not run any programs where the battery runs out, and then in the boot state to 80% of charge , repeated a few times also equivalent to manually “deep charge deep release.” In fact, this approach aims to make continuous small current laptop battery discharge, which discharge status in our daily use is unlikely to be achieved, the effect of the discharge and those dedicated basically the same software dell Inspiron 8500 battery,dell Inspiron 8600 battery,dell Inspiron 9200 battery.

One response so far

Aug 28 2009

On the use of lead-acid battery maintenance

Published by admin under battery tips

The article come from http://www.batteryoffice.com/batteryblog/2009/08/on-the-use-of-lead-acid-battery-maintenance/

Lead-acid battery is a farm trucks and tractors an important component of the electrical system. Battery life with the use of maintenance is closely related to the use of improper maintenance will cause early damage to batteries Inspiron E1405 battery , Inspiron E1505 battery.Therefore, a careful use of good battery maintenance is very necessary. In addition, the battery sometimes in the course of some damage, the user to take some temporary measures, real-time to repair, to avoid adversely affected by farming season and reduce losses.
First, the use of lead-acid battery maintenance
1, the correct installation Datie pole piles. The present agricultural vehicles and tractors on the generator with the rectifier is equipped with the battery negative Datie, and DC generator with laptop battery? is used in cathode Datie, can not hold against; otherwise the former will burn silicon diode, which will burn regulator contact. Lead-acid battery pole pile marked “+” sign is positive, marked “-” number is negative. No tags, you can identify by the following characteristics: a very thick pile is positive, smaller is the negative; great pile on the oxide is more positive, less is negative; very dark brown pile is positive, pale gray is negative; also available from the poles leads to a pile on each wire, 1K500 battery , 1X793 battery inserted in the same acid in the cup, there are a large number of bubbles produced is negative.
2, do not make excessive battery discharge. Use electric starter starts, each operation shall not exceed 5s; the first time you start Buzhe should be separated 2-3min and then start-up; three times to start Buzhao, should check the reason, can no longer start a row.
3, the winter starts, the engine to heat water, oil should be pre-heating to reduce the load to start the motor and reduce the 8N544 battery output current. In addition, there is no loose wiring clip case, do not force moving wiring chuck in order to avoid a very loose pile.
4, proper maintenance of battery should do the following:
(1), always keep batteries? HD438 battery , HF674 batter?clean. The outer surface of battery electrolyte spills, dirt, dust, which would cause short-circuit discharge must always wipe clean. Polar head piles and wiring should be kept clean, good contact, and coated with Vaseline to oxidation. Battery lid vent should be kept open in order to avoid gas expansion to enable battery shell rupture.
(2), batteries installed in the locomotive must be fastened securely, and to have anti-vibration pad, so as to avoid driving shattered battery shell. When they find the shell cracking or electrolyte leakage should be timely maintenance.
(3), regularly checked the electrolyte fluid level. Inspection, the application of two openings of the glass tube, insert a finger after a single cell block singalong, and then out observation, is strictly prohibited the use of metal utensils. Surface is insufficient, it is timely to add distilled water; as electrolyte leakage or overflow when the original density of the electrolyte should be added. Add distilled water, it should start the engine to recharge, so that electrolyte mixing.
(4), regularly check the ThinkPad T40 battery?deposit of electricity. Application of electrolyte density meter or the discharge fork measurements. When none of these devices can also be speaker volume or the intensity of light to check. Prohibit the use of short-circuit spark discharge to see the size of ways to check to ban the use of tools and objects can be conductive on the battery on the battery off to prevent short circuits.
Second, the immediate lead-acid batteries commonly damage repair
The use of the process, if the battery were damaged, the user can take some temporary measures to repair immediately to an emergency, conditional again when a thorough restoration.
1, very pile ablation, fracture. When the great pile ablation, broken after the repair can be planted wire method. Damage to the very first pile cut from the root level, in its cross-section center drill? 5mm, depth 15mm holes, screw into the M6 × 30 hexagonal screws. The iron pipe on the horn to do a very pile on the molten lead poured into the heated water, after cooling tubes can remove the speaker.
2, shell, cover cracks. If it is found in the vehicle was moving in time, they should first plugging. The side of the battery does not drain the side and wipe away the electrolyte leakage in the ASM 92P1138 battery cover at digging some sealing material, in the exhaust pipe after Hongre Trap. If the slab cracks, the application hacksaw sawing supplemented after the V-groove. For the small cracks, can be used adhesive bonding. Approach is to first crack at local heat until softened after the knife cut into V-shaped crack along a small groove and then with a good resin to be squeezed clay patch Department, Tu Ping, after paper stickers, ready to put its own house sclerosis immediately after use.
3, plate short circuit. Multi-partition is damaged or the bottom of the sediments due to too much lead. Ruoyin partition is damaged, should open the battery, replacing bulkheads. If only a single cell of the partition is damaged, can be removed separately, a single cell of the plate group repairs. Ruoyin too much sediment should be poured electrolyte, cleaned with distilled water after repeated charging.
4, very active material off the board. Active material shed much, they can continue to use after the removal of sediments.
5, plate curing. More than a long-term due to battery discharge in a discharge or semi-state, produces a very thick plate-shaped grains caused by lead sulfate. If curing is not serious, can be used for recharging small current long ways in which the active material recovery, methods of operation are as follows: first by 20h-discharge rate XD736 battery discharge end power, poured out all the electrolyte, washed several times with distilled water and then injected into distilled water to the standard liquid. The second phase of the initial charge with the charge current charge, and to keep measuring the density of electrolyte, when the density increased to 1.15g/cm3 stops charging. Then pour the entire inside of a single electrolyte, and then injected into distilled water and continue to charge. So over and over again, until no longer be increased until the density of the electrolyte. Last to conduct a discharge, and then its fully charged, the electrolyte density can be adjusted to the desired value. The charge to the vulcanization of? GW240 battery?, its capacity should be restored to the rated capacity of more than 80%. Otherwise, it should be further carried out a number of charge and discharge processing.
6, sealing plastic rupture. If the small cracks that can be used hot iron hot together. If the crack larger, severe electrolyte leakage, should eliminate, re-casting. In order to seal the shell material and a reliable combination of pouring Department should be cleaned with cotton dipped in alkaline to acid.
7, battery circuit. After the? Precision M65 battery of a single-cell circuit can be used across the open circuit wires thick enough to single-cell temporary use.

80 responses so far

Aug 28 2009

Japanese Association for Solar Power the statistical results

Published by admin under battery tips

According to the Japanese Association for Solar Power (JPEA) the statistical results showed that Japanese companies are JPEA members in 2009 first quarter (April ~ June) solar cell and module supplier by 10% compared with a year earlier, reaching 84.6MW. Exports fell by 6% year on year has fallen 201.4MW, while for Japan’s domestic shipments have increased 83% year on year, reaching 83.3MW. The reason is to restore Japan’s grant system, laptop battery was active in the domestic market trends.
From the different types of point of view, poly-silicon type solar cell supply increased by 7% compared with a year earlier, VGP-BPS9A battery reaching 149.4MW, monocrystalline silicon class year increased by 8% to 97.7MW, thin-film silicon-year increase of 31% category, to 33.6 MW. Compound class and others Sony laptop battery, JPEA classified as “other” type of an increase of 38%, to 4.0MW.Japanese Association for Solar Power the statistical results

414 responses so far

Aug 28 2009

Japanese Association for Solar Power the statistical results

Published by admin under battery tips

According to the Japanese Association for Solar Power (JPEA) the statistical results showed that Japanese companies are JPEA members in 2009 first quarter (April ~ June) solar cell and module supplier by 10% compared with a year earlier, reaching 84.6MW. Exports fell by 6% year on year has fallen 201.4MW, while for Japan’s domestic shipments have increased 83% year on year, reaching 83.3MW. The reason is to restore Japan’s grant system, laptop battery was active in the domestic market trends.
From the different types of point of view, poly-silicon type solar cell supply increased by 7% compared with a year earlier, VGP-BPS9A battery reaching 149.4MW, monocrystalline silicon class year increased by 8% to 97.7MW, thin-film silicon-year increase of 31% category, to 33.6 MW. Compound class and others Sony laptop battery, JPEA classified as “other” type of an increase of 38%, to 4.0MW.

715 responses so far

Aug 28 2009

Electric vehicle battery maintenance, the coup

Published by admin under battery tips

Electric cars have already entered our lives, in use on how to maintain the laptop battery electric cars do?
The car driving the process, should not be frequent to start, brakes, because the time consuming current, the battery negative.
Experience a more steep uphill or poor road conditions, when the get off the implementation (which can lead force), reducing the DELL laptop battery large current discharge, or easy to damage the battery.
Constant attention to the battery of power-storage and, if the phenomenon of power loss, we must promptly give charge to prevent sulfide;
When charging to charge until the green light is not suitable for half-way stop and then driving charge, so apt to vulcanization;
The car a long time when not in use, should be placed saturation charge per month to pay for additional electricity once the battery to prevent sulfide.
In addition to the Inspiron 9400 battery charger The quality of life impact is not inconsiderable, the following instructions for your reference.
Why is a good charger can extend battery life?
For a friend ride electric vehicles, in particular the configuration of high-powered motor as friends, generally six months to a year or so, we must replace the GD761 battery, how to extend extend the battery life cycle of replacement batteries for each car’s friends are very concern.
To extend battery life, in addition to and riding habits, the quality of the battery, the more closely the quality is good or bad charger. On the one hand, the battery though simple in principle, but has its own charge-discharge performance characteristics (each of the charge and discharge processes are taking place in a complex physical and chemical changes), and only consistent with this charging method, and the repair of the charger with pulse can be real sense to extend Latitude D830 battery life; the other hand, chargers and battery charging accompanied almost every day, not in conformity with battery charger features, it means the battery’s “pillow killer,” “slow poison”, overcharge or less charge will be long-term “poisoning” battery, a long time, prone to water loss, etc. affect the bulge deformation of the normal life of the battery problem, which is the industry’s often said that the “battery is not being used or bad, is filled bad” argument .
The following is the Latitude D620 battery charging and discharging and the use of the process will lead to attenuation of several aspects of the capacity factors:
1. In the battery use and charging and discharging process, there will be “curing” phenomenon affect the battery capacity.
Note: The curing process that is due to the use of batteries in the electrochemical reaction, plate will gradually be covered by the hard lead sulfate crystals, resulting in gradual reduction of active plate area and the acid concentration decreased and makes the battery capacity decline.
2. Winter and summer, the battery charging voltage is different from the absence of a suitable environment for PSA can be adjusted with the charger, will make the summer off rechargeable batteries eventually lead to water loss caused by the battery pack battery drums, distortion, or charge occurs in winter due to decreased mileage.
Note: The battery charging voltage and the ambient temperature is inversely proportional to the relationship.
3. As the HP laptop battery  factory use and a variety of factors such as compatibility of the error by connecting the battery voltage imbalance will occur between the battery capacity will be subject to the minimum voltage that the battery.
Note: Because the battery more than 3 ~ 4 12V battery thread made, use, compatibility of the error due to the battery factory and other factors, will make the battery appear inconsistent power voltage, whereas the traditional concatenation constant voltage or constant current charging mode will not solve the imbalance in voltage between the Pavilion dv2000 battery problem, the final battery capacity would be subject to a lower voltage that the battery effect of other higher-capacity battery power will not be released.
How to choose a good charger?
Based on the above Pavilion dv6000 battery problem that might arise in use, targeted to select a good charger is essential, probably to meet the following requirements:
1. With the MCU digital control, charge and discharge control parameters should conform to specific battery charge curve, the current to determine the battery is full, rather than the voltage of judge.
2. With a positive or negative pulse charging repair functions, can be shattered plates of lead sulfate crystals, repair plate activity.
3. With automatic temperature compensation function, according to the ambient temperature is different charging voltage timely adjustments to ensure that filling the summer, but winter is not less filling.
4. With a balanced charging function, can prevent the thread between the Sony laptop battery voltage inconsistencies, maintaining consistency of battery capacity.
5. Conventional reverse, short circuit, over-current over-voltage, over temperature and no-load no output protection VGP-BPS9A battery , VGP-BPS5 battery , VGP-BPS2 battery.

No responses yet

Aug 28 2009

An emergency starter battery is dead panic of three approaches

Published by admin under battery tips

Encountered no electricity or laptop battery failure of the starter motor, which need to be taken when an emergency starter
Carts start is our most familiar and most effective method of emergency start, but it is a means to not have and can not often used, because it would be the engine and clutch have some damage, automatic transmission vehicles, in particular to avoid the use of this method start. Carts start generally require two or more, if only one person would be difficult to implement the driver starting.
Safety
First, Latitude D830 battery to observe the location of road parking suitable for carts start, you can help improve the speed downhill, if the car ahead is uphill, then the cart will move forward very tired, very difficult to improve the speed, so it should be turned around the front to push the downhill direction car. Try not to vehicles and pedestrians in the number of sections carts start, after starting the driver to avoid emergency vehicles, improper accidents.
Slowly Parking
Promotion should be opened before the vehicle ignition switch, to a considerable speed, it will be put on the two transmission gear, and then quickly release the clutch pedal and the fuel. Once the engine starting, shall be promptly depresses the clutch pedal, while controlling the throttle, to prevent engine flameout, Inspiron E1505 battery and then gradually stop.
When the battery power is low, this method can be used an emergency starter.
The two vehicles approached, until adequate jumper cable to connect two Latitude D830 battery positive and negative. Should be taken to ensure that cars could not touch, only allowing the use of sufficient bearing capacity and the cable with insulated jacket. If the battery provides power to the installation location on the vehicle directly across inconvenient access, you must use a tool to remove the batteries.
To determine the positive and negative terminals of two batteries  FRU 92P1131 battery , FRU 92P1133 battery , FRU 92P1137 battery, use a cable to the positive with positive, negative and negative respectively, are linked. Should pay attention to battery positive and negative must not be mistaken, but also to ensure a reliable cable connection. Layout direction of a good cable to prevent starting when the cable and tape or fan Guaceng.

23 responses so far

Next »

Tags

compaq 319411-001 dell dell 310-6321 dell 310-6322 dell 312-0386 dell battery dell d5318 dell g5260 dell g5266 dell inspiron 6400 battery dell laptop battery dell pc764 hp 367759-001 hp f1739a hp f2019 hp f2019a hp f2019b hp f2299a hp f3172a hp f4098a hp f4809a hp f4812a hp VGP-BPS5 inspiron 6000 battery inspiron 9300 battery inspiron 9400 battery laptop battery latitude d620 battery notebook batteries notebook battery omnibook 6000 battery omnibook xe battery presario 2100 battery presario 2500 battery presario nx9000 battery presario nx9010 battery sony digital camera battery sony laptop battery Sony np-fc10 Sony np-fc11 Sony np-fe1 Sony np-fr1 Sony np-fs11 Sony np-fs21 Sony np-ft1

Search